It is dedication to learning what you want, determination to develop the right concept, and execution of that concept with care, precision, and attention to detail. See your dealer for details. The following illustration shows current accessory drive configuration. If the same error code appears in the display, try a different cartridge. Remove piston rings using a suitable piston ring expander. That station is now held in memory on that button. The vehicle should then be operated at idle speed to circulate the additive throughout the fuel system.
Attaching jumper cables Jump-Starting 1. New connecting rods were installed. Connect the fluid cooler inlet tube and oil cooler outlet tube at the radiator. Rotate the pump shaft to distribute the oil within the pump body. Install generator mounting bracket with assembled generator.
Copyright 1997 - 2019 RepairManual. Install the windage tray and tighten to 17-21 Nm 13-15 lb-ft. Disconnect the dual converter Y pipe 5F250 from the exhaust manifolds 9430. It is dedication to learning what you want, determination to develop the right concept, and execution of that concept with care, precision, and attention to detail. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Allow the same amount of distance when braking as with a two-wheel drive vehicle. Use the lug nut wrench to screw the lug nut snug against the wheel but do not tighten.
Temperature control see Climate control. Pry crankshaft forward against thrust surface of upper half of bearing. All of the warning lights and gauges alert you to possible problems with your vehicle. You should always avoid using the wrong tool or screwdriver in a vehicle as you could end up damaging screws and nuts for good by shearing off the edges. The decisions of the Board are binding on the dealer and Ford, but not on consumers who may elect to pursue other remedies available to them under state or federal law. To help you find specific information quickly, you can use the Quick Index, Table of Contents, or the Index. Remove the negative end of the jumper cable from the metallic surface on the engine or frame of the disabled vehicle.
The illustrations on the following pages show the major parts of the instrument panel that are described in this chapter. See your dealer for complete warranty information and accessory availability. Lights and Bulb Replacement It is a good idea to check the operation of the following lights frequently: headlamps high-mount brakelamp tail lamps brakelamps hazard flasher. Make sure the vehicles do not touch each other. See Engine oil recommendations in the Index.
Remove power steering pressure hose 3A719 and power steering return hose 3A713 if necessary. Mount the engine 6007 on a work stand and remove all parts not furnished with the new cylinder assembly. If you need to shift out of P Park by using the alternate procedure described above, it is possible that a fuse has blown and that your brakelamps may also not be functional. Make sure the van is supported securely on the jackstands and only work on one side at a time. When to use 1 Low Use 1 Low to provide maximum engine braking on steep downgrades. It is the responsibility of the registered owner to determine the applicability of such laws and regulations to your intended use for the vehicle, and to arrange for the installation of required equipment.
Tighten the cap to 90-104 Nm 66-77 lb-ft. Lights and Bulb Replacement It is a good idea to check the operation of the following lights frequently: headlamps high-mount brakelamp tail lamps brakelamps hazard flasher. The Board reviews all warranty performance complaints on Ford, Mercury and Lincoln cars and Ford and Mercury light trucks under the new vehicle limited warranty that have not been resolved by either a dealer or Ford Motor Company, except those involving:. Install valve tappets 6500 in their original bores. However, I may be wrong. If needed, clean the disc with an approved disc cleaner, such as the DiscwasherH Compact Disc Cleaner or the Allsop 3H Compact Disc Cleaner, by wiping from the center out to the edges.
Fan, engine fan, avoiding injury. These Ford Aerostar repair manuals cover all these sections and more:. To remove underbody temporary spare tire: 1. Position the headlamp on the vehicle and install the four attaching screws. See your Ford or Lincoln-Mercury dealer.