2004 toyota camry torque specifications. 2004 Toyota Camry Solara SLE V6 2dr Coupe Specs and Prices 2019-01-30

2004 toyota camry torque specifications

Toyota Parts

2004 toyota camry torque specifications

Rocker arms non-adjustable 18-22 ft-lbs. Pressure plate bolts 35 ft-lbs. I dont thin anything has changed on this engine since then. Cylinder head bolts 90-100 ft-lbs. Cylinder head bolts 140 ft-lbs.

Next

Toyota 3.0L

2004 toyota camry torque specifications

Pressure plate bolts 35 ft-lbs. Disconnect the anti-lock brake sense and mounting bracket. For 1963-67 427 Rocker arm shaft bolts 40-45 ft-lbs. Harmonic damper bolts 70-90 ft-lbs. For Boss 351C Cylinder head bolts 105 ft-lbs.

Next

2004 Toyota Camry Engine Torque Mount

2004 toyota camry torque specifications

Harmonic damper bolt 70-90 ft-lbs. Fastener Type Torque Spec Main cap bolts 60-70 ft-lbs Outer main cap bolts 35-40 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Next, bounce the rear of the car to stabilize the suspension. Pressure plate bolts 35 ft-lbs. After pulling the bolts of the lower side of the strut out, find the nuts connecting it to the upper frame. Replace the worn out parts and put the pieces back together in the reverse order they came off.

Next

2004 Toyota Camry Engine Torque Mount

2004 toyota camry torque specifications

Complete these procedures for the other side. Harmonic damper bolt 70-90 ft-lbs. For 406 and 427 Cylinder head bolts 80-90 ft-lbs. Connecting rod bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Dec 18, 2015 Ford Engine Bolt Torque Chart Bolt Torque Spec Chart for Ford Engines These specs are for stock-type bolts with light engine oil applied to the threads and the underside of the bolt head. Oil pump bolts 23-28 ft-lbs.

Next

Torque Specifications

2004 toyota camry torque specifications

Remove them and pull the strut out. Pressure plate bolts 35 ft-lbs. Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. These bolts should be torqued to 29 foot lb. Mar 19, 2013 1992 Toyota Camry Sedan 3.

Next

2004 Toyota Camry

2004 toyota camry torque specifications

The oil pan under the car is mounted with bolts tightened to around 80 inch-pounds. The throttle body is mounted to a torque of less than 100 inch-pounds for a V-6 engine or 20 to 22 foot-pounds for a four-cylinder. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. The pan that contains the automatic transmission fluid is mounted with its bolts tightened to approximately 69 inch-pounds; the drain plug is tightened to 35 to 36 foot-pounds. Front cover bolts 12-15 ft-lbs.

Next

SOLVED: Need torque spec for 02 camry 2.4 cam shaft bolts

2004 toyota camry torque specifications

Next, mark the front side of each head bolt with a dot of paint. Connecting rod bolts 40-45 ft-lbs. Then, jack the front end into the air and support it with jack stands. Harmonic damper bolts 70-90 ft-lbs. Connect the link nut to the strut and replace any brackets or sensors. Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs.

Next

Toyota Camry Bolt Torque Specifications

2004 toyota camry torque specifications

Cam thrust plate bolts 8-10 ft-lbs. The driver and front passenger airbags are designed to deploy in severe usually frontal collisions where the magnitude and duration of the forward deceleration of the vehicle exceeds the design threshold level. Ideally, this will be in a garage with protection from weather and with ample lighting. Intake manifold bolts 32-35 ft-lbs. The pan that contains the automatic transmission fluid is mounted with its bolts tightened to approximately 69 inch-pounds; the drain plug is tightened to 35 to 36 foot-pounds. You will start by replacing the dust cover and attaching the upper bolts on the strut to the body.

Next

Toyota 3.0L

2004 toyota camry torque specifications

Cam thrust plate bolts 9-12 ft-lbs. Crossbolts for 406-427 40 ft-lbs. In all other accidents, the airbags will not inflate. To decrease the risk of injury from a deploying airbag, always wear seatbelts, sit upright in the middle of the seat as far back as possible from the airbag modules and do not lean against the door. Intake manifold bolts 23-25 ft-lbs Oil pump bolt 23-28 ft-lbs. Torque: 70 N·m {714 kgf·cm, 52ft·lbf} c Mark the front of the cylinder head bolts with paint.

Next