2008 dodge ram 2500 cummins ecm. 2008 Dodge Ram Truck ECM ECU 4981228 6.7L Cummins 2019-03-06

2008 dodge ram 2500 cummins ecm

2008 Dodge Ram 2500 Check Engine Light: 3 Complaints

2008 dodge ram 2500 cummins ecm

The resistance as measured across the sensor terminals should be less than 1340 ohms with the engine warm. Close enough just isn't good enough when it's time to repair or replace your computer. . Then they are sealed and cleaned to give a clean appearance. Engines are test run to ensure properly starting from a cold setting and checked for blowby, unusual noises, knocks, and oil pressure. Call to inquire about all modules we are able to test and repair. When sending in your part it is necessary to take precautions to ensure that your part arrives in the same condition that it was shipped.

Next

Dodge PCM Direct

2008 dodge ram 2500 cummins ecm

Running truck that drove in to the garage. Look at the code reader or scanner's small display screen. International Buyers: Import Duties, Taxes, and charges are not included in the item price or shipping cost. Let's go over your situation or problems that you are having! Warranty is for replacement of the part only. If communication with the ecm is still possible, using a scan tool try to retrieve the trim codes from the ecm for each injector cylinder number.

Next

Dodge Cummins Diesel Engine Computers (PCM + ECM) for Sale

2008 dodge ram 2500 cummins ecm

If the voltage is not 0, the heater relay is stuck and the relay must be replaced. There will be no need for any additional programming. Replaced O2 sensors again and wrapped exhaust. We also offer drive in service if you are in the San Diego California El Cajon area. These modules are in demand for many makes and models and buying a re-manufactured one from the dealership or from an unknown internet sales company can cost double what we charge for the repair of your module, then the added unknown of needing it programmed to your vehicle can really add to the price.

Next

Ram Diesel Manifold Heater Problems

2008 dodge ram 2500 cummins ecm

The teck found the Turbo Sticking and Failed 02 sensor. Shipping and programming charges may apply. Intake Manifold Air Temperature Sensor Test 1 Disconnect the wire harness connector from the intake manifold air temperature sensor. These terminals should be grounded. Since 1918, Dorman Products has supplied the automotive aftermarket with high-quality replacement parts, hardware and fasteners. The heater will continue cycle on and off, after the engine is started, until the intake manifold reaches 60° or the truck reaches about 15 mph. Came off a running and driving truck.

Next

4931980 2006

2008 dodge ram 2500 cummins ecm

The engine 8 digit serial is located on the engine data tag located on the side of the valve cover see pics. Harness is in good condition and was removed from a good running truck. If they are not, the ground wire has broken. Contact Information: Please include your contact information when sending in your parts. Prior to 1989, Cummins was a known leader in commercial vehicles and teaming up with Dodge represented the company's first move into the medium-duty pickup arena. The remainder of the original price charged will be refunded. Sealed Key Switch With Anti-restart.

Next

4931980 2006

2008 dodge ram 2500 cummins ecm

Tambien nosotros ofrecemos un ano de garantia con la devolucion de su vieja computadora. This will usually takes 3-4 business days. Sealed Ignition Key Switch by Littelfuse Features. Si tiene alguna pregunta no dude en contactarnos. Connect your code reader or diagnostic scanner to the Dodge's Data Link Connector. Harness is greasy see pictures. When you receive your part you will be able to plug it in and start your vehicle.

Next

2008 DODGE RAM 2500/3500 CUMMINS ISB 6.7L ENGINE ECM 4980611

2008 dodge ram 2500 cummins ecm

Not bad Love the Truck. They Replaced O2 sensors 3rd time - cleaned turbo desooted. Just go ahead and call the phone number at the top of the page and a friendly specialist will help you out. Two of the wires have the insulation missing at one of the connectors. The engine 8 digit serial is located on the engine data tag located on the side of the valve cover see pics. If you have the correct voltages on the manifold heaters, the heater housing should get hot.

Next

2008 Dodge Ram 2500 TSBs

2008 dodge ram 2500 cummins ecm

You get the advantages of digital instrumentation with the look and feel of the analog gauges. Just go ahead and call the phone number at the top of the page and a friendly specialist will help you out. Repairing the vehicles original computer is almost always a better option. Thank you for reading this and for your understanding. The last 8 of the donor vin is 4G156870. We're here to help with whateveve questions or concerns. See the Preheat Cycle Time Interval Chart below.

Next

2008 Dodge Ram 2500 3500 PCM ECM ECU 6.7L Diesel

2008 dodge ram 2500 cummins ecm

The air heater elements are used to heat incoming air to the intake manifold. Thank you for reading this and for your understanding. Wire harnesses are pulled from running trucks and are generally in overall good shape unless otherwise noted, and are used as replacements for a damaged unit. Make sure you do your research if unsure on interchange. The resistance should be zero 0. Warranty does not cover shipping, labor, towing, rentals, storage, legal fees, lost wages, or any other incidental fees.

Next

Cummins Diesel Engine » harness

2008 dodge ram 2500 cummins ecm

Harness is in overall good condition and was removed from a good running truck. See product for application and installation details. We do not own or sell anything that is perfect. Pulled from 2002 dodge ram 3500 Regular cab. The one plug for the air conditioning has a piece broken off. Good used back half engine wiring harness.

Next