The first Scion xB was introduced in 2003 as a rebadged Japanese-market subcompact Toyota bB. As a matter of fact, other than poor fuel economy, difficult to start the vehicle also bothers a lot. Step 12: Reconnect the bolt from 4. The serpentine belt is located on the front of the engine block and winds around several pulleys driving various engine components: water, fuel and power steering pumps, the alternator, air conditioner compressor and possibly other accessories. Will require a torque wrench also for re install. Red and Yellow arrows correspond to the bolts in Step 8: Step 10: Slide the new alternator back through the wires, carefully, and position in place. Again, use the socket wrench to turn the tension pulley far enough so the 08 Scion xB serpentine belt replacement can be wrapped around the pulley.
Pull the belt off, remove the belt from the crank shaft pulley. Once the shock is compressed, slide the belt off the pulley and release the bar slowly. Remove the cover and expose the bolt. Choose Quality-Built and rest assured in ultimately reliable performance with each turn of the key. You dont want them breaking prematurely. Also, check the tension of your belts to make sure the alternator is spinning while the engine runs. Yes i fix my problem by disconecting the neutral suitch and reconecting it ,,they get dirty with time and dont make contact ,Is a good idea to disconect and clean as many contacts as you can and put some special grease on them to prevent other problems.
The red circle highlights the tensioner bolt you will use the 19mm socket on: Step 4: After the belt is off, locate the 10mm bolt holding the crank shaft position sensor wire and alternator wires in a loom. Reconnect the bolt and cover from step 5. Quality-Built, a division of Motorcar Parts of America, is an automotive aftermarket brand of professional-quality starters and alternators. The new belt will need more clearance to get on the pulley. Scion Xb then was only available with a 1. This pulley is attached to a very strong spring and holds the belt tight against the pulleys through its serpentine route around the engine.
Use a socket wrench with a matching socket the same size as the hex head bolt in the center of the tension pulley. Please let us know if you do not find what you are looking for. Attach the socket and set the direction to tighten the same direction the spring action allows the pulley to move. Step 2: Locate your alternator Step 3: Remove the belt from the alternator pulley by using the breaker bar and 19mm socket. Locate the bolt for the hydraulic tensioner above the idler pulley.
Remove the bolt with the 10mm socket. New belts will stretch over time. They should never hold the weight of the alternator. Turn the wrench handle, the pulley moves and the tension on the belt slackens. Coil springs and coil spring insulator are auto parts you should take care. Our complete catalog covers all Toyota genuine xB parts and accessories.
If the belt is broke, of course, this procedure for 08 Scion xB serpentine belt replacement is not necessary but reversing the procedure is necessary 2008 Scion xB serpentine belt replacement installation. The repair is now complete. Rebuild Kits include quality brand precision electronic components for the automotive, heavy duty and power sports aftermarket and are among the highest quality parts available. Once steps 4-6 are complete, move the wiring aside the best you can. This problem troubles xB drivers a lot especially in such a world that oil is at surging price.
Popular Genuine Scion xB Parts and Accessories Scion xB is a subcompact and compact car manufactured by Toyota but sold under Scion - the marque of Toyota from 2003 to 2015. Once the 08 Scion xB serpentine belt replacement is around the pulleys, allow the 2008 Scion xB serpentine belt replacement to hang freely at the bottom of the engine. And we offer the lowest-priced Scion xB auto parts to meet your requirements in quality, fitment, durability, reliability and affordability. In order to drive your Scion xB as long as possible, you need to take care of every auto part in it as good as possible. Your car might die, but you may be able to restart it with a jump start. The first generation Scion xB 2003-2006 was released in 2003 as a 5-door hatchback. All parts are backed by the manufacturer's warranty and shipped directly from Toyota dealers.
An 2008 Scion xB serpentine belt replacement too small will bind the pulleys while an 08 Scion xB serpentine belt replacement too large will just fall off. Posted on Jun 29, 2009 You need an impact wrench and large socket to get the spindle nut off, also some use star pattern bolts to hold on the hub. Reconnect the plug from step 6. And headlight, wiper blade, wiper arm, headlight bulb and fog light bulb action similarly in providing open driving vision for driver. Use your 10 mm socket and disconnect the negative terminal and set it away from the post. Entering your vehicle information in our Year Make Model selector up top, helps ensure you get an auto part that fits your car, truck or other type of vehicle.
All Scion xB genuine auto parts are provided with manufacturer's warranty. Second, suspension and cooling system failed. This will show an illustration for the proper 2008 Scion xB serpentine belt replacement route around the engine. Some models require separating the ball joints too, a spreader is helpful. Take the belt off the pulley and let it hang. . Installation is reverse of removal.
This must be done correctly. Find the tension pulley located at the bottom of the motor. Once this has been done you can turn the ratchet to release tension from the belt. Then at the 2006 New York Auto Show, the second generation Scion xB 2007-2015 was unveiled as a 5-door hatchback but at the 2007 Chicago Auto Show as a production xB. Even as a compact car, Scion xB did not need to haul or load weighty items like some full-size cars, some problems would still come for it.