Vehicle was not using Cruise Control. Saw Online That It Looks Like This Has Been An Issue With This Style Truck For Over A Year. Jan 11, 2016 Sound to me like you broke the door latch mechanism or related hardware assoiated with door lock mechanisim. The shutter assembly is crimped in place, but once removed it can be reinstalled without damaging the lock. Vehicle was not using Cruise Control. Work carefully and take notes or make sketches to help you put the door back together properly.
The Part To Do The Repair Was Not Available. The Contact Had Not Experienced A Failure. The window channel will now be loose and can be moved. A Door That Opens While Driving Increases The Risk Of Injury. Once the lock is visible, the key is inserted and turned one way, as indicated in the diagram on the grill, and then the other way Photo 58. The bracket has slotted openings for the bolts in order to allow for adjustment in the position of the latch.
It is primarily intended for Ford F-150s but most likely also applies to other Ford vehicles. Mend it Fault find Advertisements Important Attempting repairs can be dangerous. As far as I can tell, the hood lock will do you very little good in generating a new key for the vehicle, but if you should ever have to service one, here is the procedure. How To Disable AutoLocks This tech article was originally posted at FordF150. I also use two wedges placed about 10 inches apart at the front of the main window. The Dealer Did Not Give A Specific Date For When The Part Would Become Available. Use a small screwdriver to carefully pry the plate at the front of the lock free Photo 49.
Disconnect cable inner from door inner handle. Disabling the auto lock feature can save you from having to call a locksmith. Vehicle was not using Cruise Control. Once the lock and latch assembly have been removed from the bracket, the lock cylinder will pull free of the latch Photo 63. This is achieved in two steps.
The Contact Had Not Experienced A Failure. Use a small, flat screwdriver to pry it out carefully. Remove the screw mounting the cable to the door handle. Some of the early Transit Connects used the 40-bit key, but since the 80-bit key will work for both types, that is now the only one that I stock. Once I got the word out that I could service these vehicles, I started getting customers who drove 50 — 75 miles for me to make duplicate keys for them.
The Contact Received Notification Of Nhtsa Campaign Number: 16v643000 latches, Locks, Linkages However, The Part To Do The Repair Was Unavailable. I had a new key done at fords as thought the battery had gone. This tutorial will show you how to install a Jimmi' Jammer® on the following vehicles: Full size Ford E-Series Van, 1997-2014. Set the panel off to the side where it can't get damaged. If however, there is no one equipped to work on the Tibbe locks, you might want to think about getting set up to do them. This type of system tends to be very rugged and pick resistant, although several picks have come on the market specifically for the Tibbe system.
When the key is turned into the unlock position, the active retainer can be depressed. Begin by tracing the outline of the latch with a marking pen so that you can replace it exactly as it was. The Contact Received Notification Of Nhtsa Campaign Number: 16v643000 locks, Linkages, Latches However, The Part For The Recall Repair Was Unavailable. If needed, make sure the damaged door metal is straightened so plate rests level against the door. If you remove the face cap, you will have access to the shutter assembly, but nothing else. To find out how to mend it.
I use the shim to protect the weatherstripping once again when I insert the tool into the door Photo 6. Confirm that the perimeter alarm is disarmed. Your answer: Add your answer here. Photo 6 Photo 7 Disconnect the door lock and power window connectors. Remove the inside door handle. Before removing any of these bolts, carefully mark the bracket so that you can put the lock back exactly as it was mounted.
Photo 14 Note the location and position of the bolt holding the window channel in place. Try to include as much detail as possible. The lock mechanism is at the rear of the sliding door, will the solenoid be near that or buried somewhere underneath the middle of the panel now full of insulation. I've had an attempt to remove the starter from my 04 ford transit but unfortunately I've snapped the long bolt holding it in place! Also works on 1997 1998 2000 2001 2002 2003 - Duration: 18:38. Vin Tool Confirms Parts Not Available. Photo 3 Photo 4 Remove the plastic screw cover behind the inside door handle.